This is the latest recevied telemetry packets stored in our database for station/object CT2IKC-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | TX* | RX* | Digi* | V_Bat* | V_Ext* |
|---|---|---|---|---|---|
| 1754092205 | 379 Count | 608 Count | 313 Count | 0 VDC | 0 VDC |
| 1754090402 | 374 Count | 598 Count | 309 Count | 0 VDC | 0 VDC |
| 1754088598 | 369 Count | 589 Count | 305 Count | 0 VDC | 0 VDC |
| 1754086795 | 364 Count | 581 Count | 301 Count | 0 VDC | 0 VDC |
| 1754084991 | 359 Count | 574 Count | 297 Count | 0 VDC | 0 VDC |
| 1754083227 | 354 Count | 567 Count | 293 Count | 0 VDC | 0 VDC |
| 1754081423 | 349 Count | 560 Count | 289 Count | 0 VDC | 0 VDC |
| 1754079620 | 344 Count | 553 Count | 285 Count | 0 VDC | 0 VDC |
| 1754077816 | 339 Count | 546 Count | 281 Count | 0 VDC | 0 VDC |
| 1754076013 | 334 Count | 538 Count | 277 Count | 0 VDC | 0 VDC |
| 1754074209 | 329 Count | 530 Count | 273 Count | 0 VDC | 0 VDC |
| 1754072405 | 324 Count | 523 Count | 269 Count | 0 VDC | 0 VDC |
| 1754070601 | 319 Count | 515 Count | 265 Count | 0 VDC | 0 VDC |
| 1754068797 | 314 Count | 508 Count | 261 Count | 0 VDC | 0 VDC |
| 1754066994 | 309 Count | 501 Count | 257 Count | 0 VDC | 0 VDC |
| 1754065190 | 304 Count | 494 Count | 253 Count | 0 VDC | 0 VDC |
| 1754063387 | 299 Count | 487 Count | 249 Count | 0 VDC | 0 VDC |
*Used Equation Coefficients:
TX: 0, 1, 0
RX: 0, 1, 0
Digi: 0, 1, 0
V_Bat: 0, 0.01, 0
V_Ext: 0, 0.02, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)